八槽智能快充, AA/AAA 8路充电器,带放电激活功能

微信扫码

产品特性

1.1 电池类型及数量
适合同时充1-8粒AA/AAA型 Ni-MH/Ni-Cd可充电电池.

1.2 -△V关断
利用电池在充满时电压有微弱下降来结束充电,充电中电池发热小,充电效果好,可有效防止过充及欠充电,提高电池的循环使用寿命并保证其放电时间。

1.3 非充电电池识别功能
每通道均可对非充电电池及坏电池进行识别, 且对应通道LED闪烁并停止充电.

1.4  防反接功能
由于外壳的特殊结构, 可以防止电池极性的反接, 保障充电器及电池不致损坏.

1.5过电流保护功能
充电器采用恒流充电,避免电池过充现象和保证充电器的安全使用

1.6 **长充电时间保护功能
无论电池是否异常,当连续充电达到6小时,无论电池充满与否,强制停止充电

1.7 短路保护功能
将充电器电池槽输出短路,充电器应能自动保护,对应通道LED闪烁并停止充电.

1.8 低电池泄漏电流
充电器在充电结束后拔掉电源不取出电池, 电池的自然放电电流很小

1.9 涓流充电
充电器在充电结束后对还会有一个微小电流对电池进行充电, 用来弥补电池在充满电后由于自放电而造成的容量损失

1.10 记忆效应修复功能
充电电池经反复充电、放电,过充后电池发热,**终导致电池容量下降,产生记忆效应, 充电器对一些有一定记忆效应的镍氢镍镉电池具有修复功能.

1.11指示功能
LED指示灯显示充电.充电时红灯，充好亮绿灯，放电时红灯闪，拒充电时绿灯闪

1.12 脉充充电功能
充电控制器采用脉宽调制(PWM)技术,确保快速、有效充电,同时有效防止电池过充, 提高电池的循环使用寿命。

1.13 放电激活功能

充电器专用的放电激活功能，长按激活按钮3S，进入电池激活模式，对电池有修复功能

激活放电电流250mA-400mA

2.1充电特性:
2.11 输入
输入电压: 12VDC(适配器或车充)  输入电流: Iin≥1A

2.12 充电电流  AA/AAA: 1~8PCS: 500mA±20%
       
2.13 涓流充电电流   AA: 50mA ±10%

2.14 充电电压   AA 1.4VDC x 8  AAA 250mAx 8

2.15 电池泄漏电流   0.5mA MAX

2.16 短路电流      Io<10mA

原厂吸塑密封包装!

Product feature

1.1 Charger type and quantity

Suitable for charging 1-8pcs AA/AAA NI-MH/NI-CD chargeable battery.

1.2 Cut off

Using the battery at the end of the full voltage slightly down to recharge, small battery heating, the charging effect is good, avoid over charging efficiently and lack of charging, improve the cycle using life span for the battery and assure the discharge time.

1.3 Non charging battery identify function

Every channel can identify the non charging battery and bad battery, also the relevant channel LED will shine and stop charging.

1.4 Meter function

For the special structure of the case, it can prevent the reverse polarity for the battery and assure the charger and battery won’t be damaged.

1.5 Over current protection function

Using the constant current voltage for the charger, to avoid over charging and assure the safety use for the charger.

1.6 Long time charging time protection function

No matter the battery is ok or not, when charging time up to 6 hours, no matter full charging or not, it will be stopped charging.

1.7 Short circuit protection function

Charger slot output have the short circuit, charger will automatically protect, relevant channel LED shine and stop charging.

1.8 Low battery leakage current

Unplug the power cable, don’t take the battery out when charging over for the charger, natural discharge current is so small for the battery.

1.9 Trickle charge

There is  micro electric current charge for the battery when charging over, used to make up for the battery after a full charge capacity loss caused by self-discharge.

1.10Memory effect restore function

Rechargeable batteries after repeated charge, discharge and over charging, heating, cause to the battery’s volume down, arouse the memory effect, the charger has certain memory effect NI-MH, NI-CD restore function
1.11 Direction function

LED direction lights shows charging, red charging, full charging, green lights, discharging red lights flash, refusing charging, green light flash.

1.11Pulse charge

Charge controller use PWM technology, assure fast and efficient charging, avoid efficiently over charging, improve the  cycle using life span for the battery.

1.13 Activation function

Charger appropriative discharge activation function, press activation button 3S, entering battery activation modes, has the restore function, activation discharge electric current is 250mA-400mA

2.1Charing features:
2.11 Out put
Output voltage: 12VDC(adapter or car charger)  Input electric current: Iin≥1A

2.12 Charging current:  AA/AAA: 1~8PCS: 500mA±20%
       
2.13 Trickle charging current:   AA: 50mA ±10%

2.14 Charging voltage:  AA 1.4VDC x 8  AAA 250mAx 8

2.15 Battery leakage current:   0.5mA MAX

2.16 Short current:     Io<10mA

Original blister packing!